Retesting After a Positive Legionella Result: What to Do

After a positive Legionella result, you retest once the cause has been dealt with, not straight away. Review the risk assessment and fix the control failure first. Then disinfect or flush where it is indicated, and wait at least 48 hours after disinfection before taking the confirmation samples. Sample the original positive outlets plus representative points, and keep sampling on a recurring basis until results hold. This guide covers the timing, the sampling points, how to read culture and PCR results, what to do if Legionella comes back, and the records you need.
TL;DR
Do not resample the moment a result arrives. Confirm the result, location and date on the laboratory report, find the cause, and carry out remedial work first.
After disinfection, guidelines from European Legionella experts say to wait at least 48 hours before sampling, so that injured bacteria are not missed.
Resample the failed outlets and a representative spread of other points, and review the risk assessment alongside the results.
If Legionella is still found, review outstanding risk assessment actions, remove dead-legs, disinfect again where indicated and move to a run of weekly reassurance samples.
Keep results, dates, remedial work and disinfection reports for at least five years.
Table of Contents
What a positive result actually tells you
A positive Legionella result is a signal that something in the system is not under control. It is not, on its own, a diagnosis of illness or proof that anyone has been harmed. What matters is the count, the location it came from, the conditions at the time, and what the risk assessment already says about that outlet.
Start with the laboratory report. Check the sample point, the date and time of collection, the species or group reported and the count in colony forming units per litre (cfu/l). Confirm that the point on the report is the point your site team believes was sampled. Labelling errors happen, and acting on the wrong outlet wastes time and leaves the real problem in place.
The response then scales with the count. The HSE’s technical guidance, HSG274 Part 2, sets out how to interpret results and respond. In broad terms, a low count means the system is generally under control and the control scheme should be reviewed. A mid-range count calls for investigation and resampling. A high count, particularly across several outlets, calls for prompt remedial action followed by resampling. Always read the exact action levels and wording in the current guidance for your type of system, because they differ between hot and cold water systems and cooling systems.
Before you do anything else, inform the responsible person for your site and anyone who may be exposed. In healthcare, care homes, schools with vulnerable users and other higher-risk premises, speak to your infection control lead or water safety group straight away, because they may need to restrict use of the affected outlets while you work.
Why you cannot just resample immediately
It is tempting to take a second sample the next day. If it comes back clear, the problem seems to have gone away. That is the trap.
A sample taken straight after a disinfection can come back negative because the bacteria are injured rather than dead. The European guidance referenced above notes that samples should not be collected sooner than 48 hours after disinfection, because injured organisms need time to recover and can otherwise produce a false negative. A clear result from day one tells you the treatment hit the bacteria hard. It does not tell you the system is clean.
The same applies to resampling without any remedial action. If the cause of the positive was a stagnant outlet, a temperature failure or a poorly used shower, then a second sample from the same untreated outlet may give the same answer, or a different one by chance. Neither tells you anything about the cause.
The sensible order is:
Confirm the result and the sampling point.
Review the risk assessment and the control records for that part of the system.
Identify and correct the likely cause (temperatures, stagnation, dead-legs, scale, a failed thermostatic mixing valve, tank condition).
Disinfect or flush where indicated.
Wait for the recommended interval.
Resample and compare.
When to retest after remedial work
There is no single interval that suits every system, because the right timing depends on what you did and how the system behaves afterwards. Three points hold in most situations.

After chemical or thermal disinfection: allow at least 48 hours before sampling, as above. Disinfectant residuals should also have returned to the normal operating range, otherwise residual biocide in the sample can suppress growth in the laboratory and mislead the result. Ask the laboratory about neutralisation of the sample bottle for any chlorinated or otherwise treated water.
After repairs, tank cleaning or replacement: the system needs to be refilled, flushed and brought back to normal operating temperatures before it is sampled. Sampling a half-commissioned system measures the commissioning, not the control regime.
After a procedural fix with no disinfection (such as restoring flushing of little-used outlets or correcting a hot water temperature): the HSG274 approach is to resample within a short, defined period to see whether the fix has worked, then continue sampling at intervals until you have a stable run of satisfactory results.
The point of a retest is to check that your control measures are working in normal operation. It is not a single pass or fail event.
Which points to sample
The European guidance is clear that sampling should never be carried out in isolation. It has to be integrated with a review of the water system’s risk assessment and the current control measures. In practice, that shapes your sampling plan.
A sound post-remediation sampling plan normally includes:
The original positive outlets. They are the proof that the specific problem has been dealt with.
Return legs and the furthest points. On a hot water system, sample the calorifier or heater flow and return and the outlets furthest from the plant, which are the places where temperature failures show first.
Representative outlets from each zone, floor or wing. Choose a spread that reflects the layout, not just the convenient taps.
Cold water storage. If a tank was cleaned, repaired or replaced, sample from the tank and from the outlets it serves.
Little-used outlets and showers. These are the likeliest places for stagnation and for the problem to reappear.
Thermostatic mixing valve outlets. Where a TMV serves the outlet, it can be a colonisation point because of the lower blended temperature. Servicing it before resampling is often part of the remedial work.
Take the sample in the same manner as the original, or record any change. Whether you sample pre-flush or post-flush changes what the result means: a pre-flush sample shows what has been sitting in the outlet, while a post-flush sample shows the water in the system behind it. Consistency lets you compare like with like, and your risk assessment should say which approach applies to which outlet.
If you want a competent, accredited team to take the samples and a UKAS-accredited laboratory to analyse them, our Legionella water testing and analysis service starts from £55 per sample. Our guide on how to test for Legionnaires’ disease explains the process from sampling to report.
Reading culture and PCR results after treatment
Two laboratory methods turn up on retest reports, and they answer different questions.
Culture grows live Legionella from the sample and reports a count in cfu/l. It is the method that the UK action levels are written around, so it is the one to use for comparing results against HSG274 thresholds. It takes several days, because the bacteria grow slowly.
PCR detects Legionella DNA. It is fast, often a day or so, but it cannot tell you whether the bacteria it detected were alive. After disinfection, that matters a great deal: dead cells still carry DNA, so a PCR result can stay positive after a treatment that has worked.
What this means for retesting:
PCR negative: a strong indicator that culture will also be negative. A study of more than 11,000 samples found that 835 of the 870 culture-positive samples were also PCR-positive, which supports its use as a rapid negative screen.
PCR positive after treatment: not proof of failure. Published work has reported higher positive rates by PCR than by culture, possibly because of viable but non-culturable cells or residual DNA. A positive PCR is a prompt to confirm by culture, not a reason to assume the treatment failed.
Culture negative: consistent with effective treatment, provided the sample was taken at the right time, from the right points, and was properly neutralised. It is a snapshot, which is why a run of results matters more than one.
Ask the laboratory to state clearly which method was used, the detection limit and whether the lab is UKAS-accredited for Legionella in water. The accreditation matters because the whole decision chain depends on the number being right.
If the retest is still positive
A second failure is not unusual, and it usually points to a cause that has not yet been found. The checked guidance suggests a structured response. A local authority policy based on the same framework calls for reviewing outstanding risk assessment recommendations, arranging further samples and chlorination where indicated, and weekly reassurance sampling for a month or longer.
In practice, work through these questions:
Is there a part of the system that is not being reached? Disinfection only treats the water and surfaces it contacts. Redundant pipework and dead-legs allow stagnation, and HSG274 says they should be removed. A capped spur that holds water at room temperature can reseed the system after every treatment.

Are temperatures being achieved everywhere? Failures at the far end of a circulation loop, or in a cold water system that warms up in a hot plant room, can undo disinfection within days. Monitoring temperatures regularly, or continuously with automated sensors, shows whether the fix is holding. Our guide on completing temperature monitoring checks sets out the routine manual checks, and automated temperature monitoring removes the gaps between them.
Is there biofilm or scale? Heavily colonised surfaces can protect bacteria from disinfectant. A tank or calorifier in poor condition may need cleaning, repair or replacement rather than another dose of biocide.
Has the risk assessment been acted on? Open recommendations from the last assessment are the first place to look. If the assessment is old, or the system has been altered, reviewing the Legionella risk assessment is the right next step.
Are users protected in the meantime? Where results stay positive in areas used by vulnerable people, the usual interim measures are restricting use of the affected outlets, fitting point-of-use filters where appropriate and involving your infection control team. Our article on Legionella risk management for immunocompromised patients covers this setting.
When the cause is found, disinfect again where indicated, wait the recommended interval, and resample.
Does a negative retest mean you are finished?
No. A negative retest tells you the treatment worked on the day of sampling. It does not replace the control regime that keeps the system safe afterwards.
The HSE explains that routine microbiological monitoring is not usually required for hot and cold water systems, while open systems such as cooling towers should be tested at least quarterly. The same page says testing may be necessary if control effectiveness is in doubt, or if temperatures or disinfection concentrations are not consistently achieved. A system that has just had a positive result fits that second description, which is why a period of follow-up sampling is normal after a failure.
A practical follow-up pattern looks like this:
Stage | What you do | Purpose |
Immediately | Confirm result, inform responsible person, restrict use where needed | Protect users while you investigate |
Remedial | Fix the cause, disinfect or flush as indicated | Remove the source of the failure |
48 hours or more after disinfection | Resample original positives and representative points | Check the treatment worked |
Following weeks | Weekly reassurance sampling for a month or longer, if the policy or risk assessment calls for it | Show the result is stable, not a one-off |
Ongoing | Return to the control scheme: temperatures, flushing, inspections, reviews | Keep it that way |
The length of the follow-up period is a decision for the dutyholder, based on the risk assessment and advice from a competent person. It should be written down, along with the reason for it.
Records you need to keep
A retest that is not recorded is hard to defend. The Approved Code of Practice L8 requires that records of monitoring, tests and inspections, including test results, dates, remedial work and cleaning or disinfection reports, are kept for at least five years.
For each positive and each retest, file:
The laboratory report, with method, count, sample point, date and time.
A record of the sampling visit: who took the samples, whether they were pre-flush or post-flush, and conditions at the time.
What was found to have caused the failure, and the remedial work done, with dates and contractor details.
Disinfection records, including the product, concentration, contact time and flush-out.
The decision on the follow-up sampling period, and who made it.
Updates to the risk assessment and logbook.
These records are what an enforcing officer, an insurer or an auditor will ask for. Clear records also help your own team see patterns, such as the same outlet failing twice a year.
In our experience, the sites that get through a positive result fastest are those that treat it as a question about the whole system, not about one tap. A failed outlet is the visible end of a story that often starts with a dead-leg, an under-used wing, a thermostatic mixing valve that has not been serviced, or a temperature gap that nobody was measuring. That is why we build the retest into a wider plan. We look at the risk assessment first, agree the remedial work, sample at the right time and from the right points, and set up the follow-up so that there is a clear route back to routine control. Our service is designed around your site and your system, with the documentation that shows what was done and why. Where the same problem keeps recurring, we would rather find the cause than keep repeating the test. Tank cleaning and disinfection, TMV servicing, remedial pipework and continuous temperature monitoring are all part of what we can provide, so one team can take you from the result to a documented fix. Sammi
Our view: treat a positive as a system problem
Getting help with retesting and remedial work
If you have had a positive result and need the next steps handled, we work with facilities managers, estate managers and compliance managers across the UK in commercial, education, healthcare and housing settings. We can review the result against your risk assessment, carry out the sampling, arrange the remedial work and set up the follow-up.
[

The main routes are:
Legionella water testing and analysis, from £55 per sample, including microbiological, Pseudomonas, TVC, chemical and closed system testing.
Water tank cleaning and system disinfection, including cold water tank repair or replacement and ongoing maintenance contracts.
TMV servicing and remedial works to correct the faults that cause repeat failures.
Legionella risk assessments, from £185, when the existing assessment is out of date or the system has changed.
If your staff need to understand what the result means and what they should do on site, Legionella awareness training is available on site or online.
FAQ
How soon can I retest after disinfection?
Wait at least 48 hours after disinfection before sampling. European technical guidance explains that injured bacteria need time to recover, and sampling earlier can give a false negative. Check that disinfectant residuals are back in the normal range and that the laboratory neutralises the sample bottle appropriately.
Do I need to retest every outlet?
Not necessarily. You should retest the outlets that failed, plus a representative spread across the system, including the furthest points, little-used outlets, storage tanks and mixing valve outlets. Your risk assessment and the competent person advising you decide the exact list.
Is a positive PCR after treatment a failure?
Not automatically. PCR detects Legionella DNA, which can come from dead cells, so it may stay positive after successful treatment. Confirm with culture, which measures viable bacteria and is the method the UK action levels are written around.
What if the second sample is still positive?
Go back to the cause. Review any open risk assessment actions, remove dead-legs, check temperatures and tank condition, disinfect again where indicated and move to weekly sampling for a month or longer. Restrict use of the affected outlets and involve your infection control team if vulnerable people are exposed.
How long should I keep retest records?
For at least five years, under the Approved Code of Practice L8. That includes the laboratory results, dates, remedial work and disinfection reports.
Sources
HSE, Testing and monitoring your water system for Legionella
HSE, Legionnaires’ disease: The control of Legionella bacteria in water systems (L8)
Control of Legionella Bacteria in Water Systems Policy, Broxtowe Borough Council (2021)
Next Day Legionella PCR: a highly reliable negative screen, Journal of Water and Health
Recommended

Comments